Megalextoria
Retro computing and gaming, sci-fi books, tv and movies and other geeky stuff.

Home » Archive » net.micro.amiga » Problem with Amigaterm.c and Lattice 3.03
Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend 
Switch to threaded view of this topic Create a new topic Submit Reply
Problem with Amigaterm.c and Lattice 3.03 [message #282352] Tue, 21 January 1986 19:15 Go to next message
AFA-DFSEC is currently offline  AFA-DFSEC
Messages: 4
Registered: December 1985
Karma: 0
Junior Member
Article-I.D.: caip.1055
Posted: Tue Jan 21 19:15:27 1986
Date-Received: Thu, 23-Jan-86 21:56:46 EST
Sender: daemon@caip.RUTGERS.EDU
Organization: Rutgers Univ., New Brunswick, N.J.
Lines: 17

From: AFA-DFSEC@GUNTER-ADAM.ARPA

I was recently trying to implement kermit protocals into Michael Mounier's
Amigaterm.  I compiled it with 3.03 and got no error messages but when the
program fired up I got a CLI TASK HELD error and then a guru meditation number.

I checked through the code, even tried recompiling the original with the same
results.  I have narrowed it down to the Serial Port stuff but am stuck there.

If I take out the OPen serial all works fine, or if I take out the SetMenuStrip
all works fine.  Any ideas would be nice.  If I get this problem overcome I
gladly post Amigaterm with Kermit protocals.

By the way, Aterm does compile under 3.02 but my kermit code does not. It gets
a CZXERR in pass 2.  HWELP!!
Glenn Watt
-------
Re: Problem with Amigaterm.c and Lattice 3.03 [message #282365 is a reply to message #282352] Wed, 22 January 1986 15:58 Go to previous message
cem is currently offline  cem
Messages: 155
Registered: May 2013
Karma: 0
Senior Member
Article-I.D.: intelca.192
Posted: Wed Jan 22 15:58:45 1986
Date-Received: Fri, 24-Jan-86 21:34:15 EST
References: <1055@caip.RUTGERS.EDU>
Organization: Intel, Santa Clara, Ca.
Lines: 28

I have the same problem, any hints from Amiga or Lattice on what they 
may have changed in the SetMenuStrip call between V3.02 and V3.03?

--Chuck

 >  From: AFA-DFSEC@GUNTER-ADAM.ARPA
 >  
 >  I was recently trying to implement kermit protocals into Michael Mounier's
 >  Amigaterm.  I compiled it with 3.03 and got no error messages but when the
 >  program fired up I got a CLI TASK HELD error and then a guru meditation number.
 >  
 >  I checked through the code, even tried recompiling the original with the same
 >  results.  I have narrowed it down to the Serial Port stuff but am stuck there.
 >  
 >  If I take out the OPen serial all works fine, or if I take out the SetMenuStrip
 >  all works fine.  Any ideas would be nice.  If I get this problem overcome I
 >  gladly post Amigaterm with Kermit protocals.
 >  
 >  By the way, Aterm does compile under 3.02 but my kermit code does not. It gets
 >  a CXERR in pass 2.  HWELP!!
 >  Glenn Watt
 >  -------

-- 
                                            - - - D I S C L A I M E R - - - 
{ihnp4,fortune}!dual\                     All opinions expressed herein are my
        {qantel,idi}-> !intelca!cem       own and not those of my employer, my
 {ucbvax,hao}!hplabs/                     friends, or my avocado plant. :-}
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic: Re: What's BCPL?
Next Topic: hack source posting delayed
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Fri Apr 26 05:35:33 EDT 2024

Total time taken to generate the page: 0.13940 seconds