Megalextoria
Retro computing and gaming, sci-fi books, tv and movies and other geeky stuff.

Home » Digital Archaeology » Computer Arcana » Commodore » Commodore 8-bit » using StereoPlayer V10.3 with Super CPU issue
Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend 
Switch to threaded view of this topic Create a new topic Submit Reply
using StereoPlayer V10.3 with Super CPU issue [message #400540] Fri, 25 September 2020 14:02 Go to next message
Anonymous
Karma:
Originally posted by: traym...@gmail.com

Hi I have come across an issue with the Super CPU running the older
CGSC STEREOPLAYERV10.3

I have come across an issue running on either a C64C or a 128DCR:

Setup as follows:

C64C or C128DCR(running in 64 mode)
Using either a V1 SUPER CPU or V2 SUPER CPU
Accessing Sid files etc using: UIEC2SD
STEREO PLAYER V10.3

The computer can be on for at least 3 hours loading and playing SID music
( the CGSC SIDS) so then at least AT 3 hours then just the IEC serial port seems to lockup, then when I try to load a Sid file the drive wont even
load anything.

So then I did some hardware swapping:
I removed my UIEC2SD and tried a floppy drive, same thing the IEC serial port just seems to hang (or something else).
I plugged my IEC2SD back in, removed my Super CPU, tried loading a Sid file again, walla then any Sid files will then load okay.

I tried this also on my 128DCR with the UIEC etc and the same
IEC lockup occurs, again remove the Super CPU and then lockup dissapears.

On my V2 C64 Super CPU I removed the main cover (years ago) and the
cooling issue is easy. And NO I am very careful not to drop anything metal into the SCPU main board. :)
My V2 SCPU I installed a small 486 Cooling fan into the main case, I mainly use this SCPU with my 128DCR's, I tapped into the 12V side of the power source to power the cooling fan, ( with the SCPU cover installed) and running the Wave Browser to really run the Super Ram hard, the Fan does spin faster and never did overheat..

I dont think this is a cooling issue beause the computer doesnt lockup and the Super Ram doesnt lock the system up either.
This only occurs after 3 to 4 hours of operation and then I cant
load any Sid files, the IEC serial port seems to be locked up and the
Disk drive wont even respond.

Any suggestions of what this might be, any possible fixes?
Re: using StereoPlayer V10.3 with Super CPU issue [message #401992 is a reply to message #400540] Wed, 11 November 2020 15:56 Go to previous message
Anonymous
Karma:
Originally posted by: traym...@gmail.com

On Friday, September 25, 2020 at 12:02:37 PM UTC-6, traym...@gmail.com wrote:
> Hi I have come across an issue with the Super CPU running the older
> CGSC STEREOPLAYERV10.3
>
> I have come across an issue running on either a C64C or a 128DCR:
>
> Setup as follows:
>
> C64C or C128DCR(running in 64 mode)
> Using either a V1 SUPER CPU or V2 SUPER CPU
> Accessing Sid files etc using: UIEC2SD
> STEREO PLAYER V10.3
>
> The computer can be on for at least 3 hours loading and playing SID music
> ( the CGSC SIDS) so then at least AT 3 hours then just the IEC serial port seems to lockup, then when I try to load a Sid file the drive wont even
> load anything.
>
> So then I did some hardware swapping:
> I removed my UIEC2SD and tried a floppy drive, same thing the IEC serial port just seems to hang (or something else).
> I plugged my IEC2SD back in, removed my Super CPU, tried loading a Sid file again, walla then any Sid files will then load okay.
>
> I tried this also on my 128DCR with the UIEC etc and the same
> IEC lockup occurs, again remove the Super CPU and then lockup dissapears.
>
> On my V2 C64 Super CPU I removed the main cover (years ago) and the
> cooling issue is easy. And NO I am very careful not to drop anything metal into the SCPU main board. :)
> My V2 SCPU I installed a small 486 Cooling fan into the main case, I mainly use this SCPU with my 128DCR's, I tapped into the 12V side of the power source to power the cooling fan, ( with the SCPU cover installed) and running the Wave Browser to really run the Super Ram hard, the Fan does spin faster and never did overheat..
>
> I dont think this is a cooling issue beause the computer doesnt lockup and the Super Ram doesnt lock the system up either.
> This only occurs after 3 to 4 hours of operation and then I cant
> load any Sid files, the IEC serial port seems to be locked up and the
> Disk drive wont even respond.
>
> Any suggestions of what this might be, any possible fixes?

NEW UPDATE ON THIS ISSUE:
I had this happen again and yes this does lock the computer up.
It finally occured to me that maybe the STEREOPLAYERV10.3 system files may be corrupted.
I recopied those and then so far this problem has no come up again but I think this was the issue
and so it may not be the SUPER CPU causing the problem.
  Switch to threaded view of this topic Create a new topic Submit Reply
Previous Topic: Commodore repairs in the U.S.A.
Next Topic: Stereo Player wouldnt load Sid files
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ] [ PDF ]

Current Time: Thu Mar 28 12:11:14 EDT 2024

Total time taken to generate the page: 0.02639 seconds