Term-mite and ZRT-80 boards.... [message #93365] |
Wed, 03 July 2013 02:25 |
jnelson
Messages: 2 Registered: July 2013
Karma: 0
|
Junior Member |
|
|
Message-ID: <1207@trwrba.UUCP>
Date: Sat, 5-Jan-85 19:34:00 EST
Article-I.D.: trwrba.1207
Posted: Sat Jan 5 19:34:00 1985
Date-Received: Tue, 8-Jan-85 04:10:10 EST
Organization: TRW EDS, Redondo Beach, CA
Lines: 11
Xref: watmath net.micro:9017 net.info-terms:457
Both the Micromint Term-mite and the Digital Research terminal boards
look to be reasonably good. The Term-mite is about $250 while the
ZRT-80 is $129.... a significant cost difference.
Can anyone sway me towards either one of these boards? Any personal
experiences that would be helpful in selecting a REAL inexpensive
terminal board?
seismo!hao!hplabs!sdcrdcf!trwrb!trwrba!jnelson
- John
|
|
|
Re: Term-mite and ZRT-80 boards.... [message #93383 is a reply to message #93365] |
Wed, 03 July 2013 02:25 |
cem
Messages: 155 Registered: May 2013
Karma: 0
|
Senior Member |
|
|
Message-ID: <474@intelca.UUCP>
Date: Thu, 10-Jan-85 11:14:00 EST
Article-I.D.: intelca.474
Posted: Thu Jan 10 11:14:00 1985
Date-Received: Sat, 12-Jan-85 05:52:07 EST
References: <1207@trwrba.UUCP>
Organization: Intel, Santa Clara, Ca.
Lines: 24
Xref: watmath net.micro:9037 net.info-terms:462
Having built several ZRT-80 boards (now $99) to upgrade some really dumb
terminals in school I offer the following comments :
The ZRT is based on the Z-80 as the controlling processor. This allows easy
custimization of the software/firmware (supplied on 8" disk) on a CP/M system.
The TERMITE uses a national chip that is not well supported in terms of tools
available for HOME computers. The ZRT-80 can have several more pages of video
ram added, with the advantage of giving either larger displays or scroll back
capability. The TERMITE does have Double high and Wide characters which
allows true VT100 emulation, the ZRT80 does not. The ZRT80 emulates the
Heath mode only (Not the ANSI mode) of a H19 terminal but could be rewritten
to add the ANSI 3.64 features. The TERMite board is physically smaller but
not by much. Serial communication capabilities are the same.
Bottom line : For what you would pay for the TERMmite you can have a complete
Terminal based on the ZRT80.
--Chuck
--
- - - D I S C L A I M E R - - -
{ihnp4,fortune}!dual\ All opinions expressed herein are my
{qantel,idi}-> !intelca!cem own and not those of my employer, my
{ucbvax,hao}!hplabs/ friends, or my avocado plant. :-}
|
|
|
Re: Term-mite and ZRT-80 boards.... [message #111923 is a reply to message #93365] |
Mon, 16 September 2013 13:25 |
notes
Messages: 111 Registered: May 2013
Karma: 0
|
Senior Member |
|
|
Message-ID: <274@isucs1.UUCP>
Date: Sun, 27-Jan-85 02:01:39 EST
Article-I.D.: isucs1.274
Posted: Sun Jan 27 02:01:39 1985
Date-Received: Mon, 4-Feb-85 04:45:32 EST
Sender: notes@isucs1.UUCP
Organization: Iowa State University
Lines: 19
Nf-ID: #R:trwrba:-120700:isucs1:9500003:000:880
Nf-From: isucs1!drew Jan 24 16:15:00 1985
I assembled a ZRT-80 board about 6 months ago and I can highly recommend it.
It is a very high-quality kit with locking dipswitches and machined-pin sockets
for the 40-pin chips (socket cost > $5). I soldered the thing together in
about 3 hours, hooked it up to my old SOL-20 keyboard and a modem and dialed
up the university VAX with absolutely no problem! The documentation is good,
but it is sketchy on theory of operation and customization of the rom program
(Maybe this information is on the disk, but my disk system isn't up yet).
DRC has put out an excellent product, and anyone who is in the market for
a quality low-priced terminal (and doesn't mind doing a little soldering
and other such work) would be well advised to buy at least one ZRT-80.
(By the way, this response was entered on my ZRT-80 in H19 mode.)
Jeff Henkels
|
|
|